CLICK TO CLOSE THIS WINDOW
CLICK TO CLOSE THIS WINDOW
Search
Pools
Our pools are made in the USA. Be sure to avoid the low priced Chinese and Japanese pools that are floating around the market. They carry no warranty. Above ground pools come in round and oval shapes and are made from a wide variety of material. If you are looking for an entry level pool system you may look toward the Yorkshire above ground pool models which are made of galvanized steel and are economically priced. We also offer the top of the line Oxford above ground swimming pool made from aluminum which will last virtually forever! Other pools such as the Paradise is made from resin materials making it safe for salt water pools.
Shop Pools >>
<< Back
Installation Process
Digging Your Pool
You will be supplied with a dig sheet like the one to the left. This is the measurements you will use to remove the earth. There will be a two foot over dig to allow for a concrete footer to secure the pool walls at the base. When excavating the bottom of the pool it is important to be as precise as possible to make the rest of the installation easy. This is the foundation of your pool. Just like a house, you will be building off this foundation. A level foundation will make for a long lasting pool structure.
Wall Structure and Installation
Now you will install your pool walls. These are lined up around the edge of the two foot over dig table. Your panels are bolted together, making sure the panels are level through each step of the process to ensure the liner will fit properly. While the pool panels are being bolted together the braces that keep the pool panels standing upright are installed. The braces help to maintain the pool shape and integrity during the installation process. The braces will be concreted in place to additional strength.
Plumbing
Your plumbing is a very important step in the inground installation process. You are going to want to be able to control the water flow to each part of your pool. So take your time to design a plumbing layout to give you the most control of returns, skimmers, main drains, etc. Plumbing can be done with flex hose or hard pipe. We prefer our customers to use flex hose under the ground. This limits the number of joints and possible leak areas. It also reduces the amount of times the water must make a 90 turn which causes restricted waterflow. There is a basic diagram to the left, however your pool should be plumbed to fit your needs.
Coping and Deck
Picking your pool coping/deck type go hand in hand. Are you looking for a nice smooth concrete deck? Then you are wanting to go with the bullnose coping and trimline style step. This is a high profile coping with a nice rounded surface. If you prefer pavers then the cantiliver coping and cantilever style step is the choice for you. Cantilever is a low profile meant to allow pavers closest to the pool to hang over to give you an edge determined be the side of the coping.
Floor and Concrete Footer
Your concrete footer should be poured atleast 8 inches tall. It is okay for the concrete footer to flow underneath the panel if there is any space but it is best to not let it get into the pool. During the pouring and drying process clean up any concrete that may run through. After the footer dries you are ready to put down your sand/mortar floor. This will be trowelled 2 inches high and will cover up 2 inches of the inground pool panels. After your floor has dried you should sweep to be sure that no extra sand or debris has made its way into the pool.
Liner Installation
The liner should be layed out in the bottom of the pool, rolled out and let to sit for a few hours to make sure it will be able to stretch a little when installing. Now you will snap the bead of the liner into the the bead track on the bottom side of your pool coping. Before you are completely done with this leave enough liner out of the bead track to allow for a vacuum hose to be inserted between the liner and the pool wall. Once the vacuum is turned on it will suck the air from the liner and rid the pool of wrinkles.
Filling the Pool
It is now time to start filling you pool with water. While the pool is being filled with water the area between the panels and the earth should be back filled with a back fill dirt to let water run through and disperse into the ground. You do not want to cut anything out of the liner at this time (light hole, skimmer, returns, step , etc). Let the pool water get just below the hole to be cut before any incision is made. If a cut is made before the liner will continue to stretch and the hole will not line up.
Network Error!
There does not appear to be an Internet connection.

Please ensure you are connected to the Internet and try processing your request again.
OK
Our Merchant Partners Offer:
No payments or interest for 6 months
Buy now and pay after summer is over!
Free layaway plans for up to 6 months
Price Matching of all products from competitors
100% Shopper Safe Secure Websites
Online coupons valued up to $1200 off purchases
Items shipped same day from local warehouses